Paradyne ENE2020-P Uživatelský manuál stáhnout pdf

ENE2020-P and ENE2020-S

2-Port E1 Network Extenders Installation Instructions

Document Number ENE2-A2-GN10-10

September 2005

Contents

Software and Firmware License Agreement ................................................. 1

Product Documentation ................................................................................ 3

Warranty, Sales, Service, and Training Information ...................................... 3

Package Contents ......................................................................................... 3

Powering Up the ENE2020 ........................................................................... 4

Configuring the E1 Ports ............................................................................... 5

Connecting the E1 Lines ............................................................................... 8

Connecting the Ethernet Line ....................................................................... 9

LED Indicators .............................................................................................. 10

RJ45 Pin Assignments .................................................................................. 12

EMI Notices .................................................................................................. 13

Important Safety Instructions ........................................................................ 14

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply to the

software and/or firmware (individually or collectively the “Software”) incorporated into

the Paradyne product (the “Product”) purchased by you and any derivatives obtained

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - Contents

1ENE2020-P and ENE2020-S2-Port E1 Network Extenders Installation InstructionsDocument Number ENE2-A2-GN10-10September 2005ContentsSoftware and Firmwar

Strany 2

10LED IndicatorsThis document describes units manufactured after 13 January 2005. See the prior version of this document for information about units m

Strany 3 - Product Documentation

11Power Solid GreenENE2020 is operational If the Power LED is not illuminated, it is unlikely that the ENE2020 is receiving power and therefore none o

Strany 4 - Powering Up the ENE2020

12RJ45 Pin AssignmentsE1 RJ45 Pin AssignmentsIf you are using a shielded E1 cable for your network connection, it must be grounded through pins 3, 6,

Strany 5 - Configuring the E1 Ports

13EMI NoticesUnited States – EMI Notice:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to P

Strany 6 - Frame Type

14Important Safety Instructions1. Read and follow all warning notices and instructions marked on the product or included in the manual.2. Do not allow

Strany 7 - Line Code

Strany 8 - Connecting the E1 Lines

16*ENE2-A2-GN10-10**ENE2-A2-GN10-10*

Strany 9 - Connecting the Ethernet Line

2from the Software, including any copy of either. If you have executed a separate written agreement covering the Software supplied to you under this p

Strany 10 - LED Indicators

38. This Agreement and the license granted under this Agreement shall be terminated in the event of breach by the Licensee of any provisions of this A

Strany 11 - Table 6. LEDs (2 of 2)

4Powering Up the ENE2020Plug the power supply into the power adapter port on the back of the ENE2020 and connect it to your power source. Verify that

Strany 12 - RJ45 Pin Assignments

5Configuring the E1 PortsConfiguration Switches for both E1 Port 1 and E1 Port 2 are numbered from left to right, 1–8.Table 1. Configuration Switch Se

Strany 13 - EMI Notices

6SpeedOn the ENE2020-P (only), switches 1 and 2 control the port speed.The E1 lines each have 31 channels continually running at 64 kbps for a collect

Strany 14 - Important Safety Instructions

7Line CodeSwitch 4 sets the Line Code for Ports 1 and 2 on both the ENE2020-P and the ENE2020-S. Switch 4 controls the line code of both E1 ports (Por

Strany 15

8Connecting the E1 LinesThe primary feature of the ENE2020 is loop bonding capability, although both the provider and subscriber units are able to fun

Strany 16 - *ENE2-A2-GN10-10*

9Connecting the Ethernet LineThe 10/100BaseT Ethernet Port auto-negotiates speed and duplex mode in accordance with the remote equipment to which it i

Komentáře k této Příručce

Žádné komentáře

Paradyne ENE2020-P Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Sítě Paradyne ENE2020-P. Paradyne ENE2020-P User's Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Sítě Paradyne ENE2020-P